XBee Explorer Dongle v2


This is the XBee Explorer Dongle unit for the Digi XBee module line. With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee. No cables needed. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version.


  • The on-board voltage regulator is good up to 500mA.
  • The highlight of this board is an FT231X USB-to-Serial converter. That’s what translates data between your computer and the XBee.
  • Reset button
  • Voltage regulator to supply the XBee with plenty of power.
  • Four LEDs that’ll help if you ever need to debug your XBee: RX, TX, RSSI (signal-strength indicator)
  • Power indicator.

This board also breaks out each of the XBee’s I/O pins to a pair of breadboard-compatible headers. So if you want to make use of the XBee’s extended functionality, you can solder some header pins into those, or even just solder some wire.

Quantity : 2

iPad mini + Cellular + Wifi with Griffin Survivor Case


Ipad Mini Information

To see how the mobilities lab has used this click here.

  • 7.9″ Retina Display: 2048 x 1536 screen resolution.
  • iPad mini is powered by the new 1.3Ghz A7 chip with 64-bit architecture. A7 delivers killer performance – up to four times faster CPU and up to eight times faster graphics performance than the previous generation – without sacrificing battery life.
  • Up to 10 hour battery life.
  • FaceTime HD and iSight Cameras: Built-In 5 MP webcamand a built-in 1.2 MP front facing camera.
  • iPad mini delivers twice the Wi‑Fi performance of its predecessor.

For more information click here.

Survivor Case Information

  • Independently tested and certified to meet conditions outlined in US Department of Defense MIL-STD-810
  • Integral Display shield deflects wind and rain (Test: up to 200 mm/hr for 1 hour)
  • Rigid internal frame protects against shocks and drops (Test: drop on flat concrete surface from 6’/1.8 m)
  • Sealed ports block blown sand and dust (Test: up to 18 m/sec for 1 hour)
  • Silicone cladding blocks vibration (Test: 18 hrs at 20 to 2000 Hz)
  • Includes multi-position workstand

Quantity : 11

LG Pocket Photo PD241T Printer Paper

Portable printer that allows you to print on the go using Bluetooth.


New LG Pocket Photo PD241T Printer + Zink Photo Paper + Cover


  • Contents: LG PD241T Printer White + Zink Photo Paper 30 Sheets + Atout Brown Case
  • Synchronization support for Windows Phone 8.0 or higher, iOS v5.1 or higher, Android v2.2 or higher.
  • No Ink required. Bluetooth wireless connectivity. Micro USB port for charging battery. Not NFC-enabled // Zink Inkless Printing Embeds Color Into The Paper: 2 x 3″ (7.6x5cm)
  •  Enable to print film when printer with case on. The case features LED indicator hole, power connect hole and power button hold.

Quantity : 1


Zink Media 2×3″ Zero ink Photo Paper for LG Pocket Photo


  • ZINK Ink Cartridges for LG Pocket Photo PD221,PD233, PD239 Printer
  • Zink Inkless Printing Embeds Color Into The Paper
  • Smudge-proof, water resistant, tear-resistant photos
  • Photo Size : 2″ x 3″

Quantity : 5



  • Peel-off, sticky back photo paper
  • ZINK Ink Cartridges for LG Pocket Photo PD221,PD233, PD239 Printer (Sicker type)
  • Zink Inkless Printing Embeds Color Into The Paper
  • Smudge-proof, water resistant, tear-resistant photos
  • Photo Size : 2″ x 3″

Quantity : 1

GoPro Hero 4 Silver



To see the mobilities lab use it in action click here.

  • Features a built in touch display to control the camera just view, tap and swipe the screen.
  • Captures 4K (15fps), 2.7K (30fps), 1440p (48fps) 1080p (60fps) and 720p (120fps) video with life-like clarity plus 12MP photos at a staggering 30fps.
  • HiLight Tag which lets you tag video highlights for easy playback, editing and sharing.
  • The Hero4 shoots beautifully detailed 12 megapixel images at up to 30 frames per second too.
  • Connect to the GoPro app on your phone to have even more control.
  • With Protune, you can tweak your settings until their just right. Adjust colour levels, ISO, exposure and more for your own personal take on the action.
  • Customise exposure settings up to 30 seconds for single and time lapse photos.

For more information click here.

Kit Includes

  • HERO4 Silver Camera with Built-In Touch Display
  • Standard Housing 131¹(40m)
  • Skeleton + Touch Backdoors
  • Rechargeable Battery
  • Curved Adhesive Mount
  • Flat Adhesive Mount
  • Quick Release Buckles
  • 3-Way Pivot Arm (Mounting Hardware)
  • USB Cable

Quantity : 1

Advanced Active Backpack


The Active Backpack I is a high-capacity yet compact rucksack that can also be used as a standard daypack. It has the capacity to hold a DSLR system with 2 standard lenses, 15” laptop as well as other personal items and accessories.
The bag has four zippered compartments with the top part designed for personal items and the bottom for photo gear. Plenty of accessories will fit inside including items such as flash, laptop, documents or even an iPad. A removable bottom insert allows you to transform the rucksack into a handy daypack.

For more information click here.


  • Weight – 1.2kg
  • Dimensions (L x H x W) – 31 x 46 x 23 cm

Quantity ; 1

GoPro Hero 4


The GoPro Hero 4 is a HD-quality, waterproof and shockproof video recording device, ideal or sport and mobility purposes. GoPro cameras are renowned for being portable and lightweight, whilst still delivering amazingly crystal-clear video.

To see the mobilities lab use it in action click here.


  • Delivers slow motion footage at 240 frames per second.
  • Waterproof up to 40 metres underwater.
  • Control of ISO Limit and exposure.
  • Time Lapse settings.
  • Audio captures clean sound 2x the dynamic range.
  • Settings for Ultra Wide field of view to change perspective.
  • Compatible with all GoPro Mounts.
  • GoPro App available to control camera remotely.
  • Resolution Options – 4K30, 2.7K60,1 1080p120, 720p2401

For more information click here.

Box Contents

  • HERO4 Black Camera
  • Standard Housing 131’(40m)
  • Skeleton Backdoor
  • Rechargeable Battery
  • Curved Adhesive Mount
  • Flat Adhesive Mount
  • Quick Release Buckles
  • 3-Way Pivot Arm (Mounting Hardware)
  • USB Cable

Quantity : 1

LilyPad Technology

LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They’re even washable, but remove batteries.

For more information about the LilyPad technology click here.


Lilypad LED White (5pcs)


  • Simple very bright
  • 250mcd
  • White LED LilyPad.

Quantity : 5


Lilypad light sensor

With exposure to daylight, this sensor will output 5V. Covering the sensor with your hand, the sensor will output 0V. In a normal indoor lighting situation, the sensor will output from 1 to 2V.


  • 20mm outer diameter
  • Thin 0.8mm PCB
  • Light sensor that outputs an analog value from 0 to 5V.

Quantity: 1


Lilypad power supply

This board was designed to be as small and inconspicuous as possible. Pop in a AAA battery, flip the power switch, and you will have a 5V supply to power your LilyPad circuit.


  • 56x26mm
  • Thin 0.8mm PCB
  • Good up to 200mA. Short circuit protected.
  • This board has AAA battery clips but can use an input from 1.2V to 5V.
  • Our lithium polymer batteries are a good, rechargeable alternative.

Quantity : 1


LilyPad Temperature Sensor

The MCP9700 is a small thermistor type temperature sensor. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.


  • 20mm outer diameter
  • Thin 0.8mm PCB
  • This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C.

Quantity : 1


LilyPad Accelerometer ADXL335

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 MEMS accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and vibration.

The ADXL335 outputs a 0V to 3V analog signal on each of the X, Y, and Z axis. You will need to convert this analog voltage to a gravity amount and use trigonometry to calculate a true ‘angle’. If you are not looking for tilt, it is very easy to use this sensor for basic motion sensing.


  • 20mm outer diameter
  • Thin 0.8mm PCB

Quantity : 1


LilyPad Vibe Board

Apply 5V and be shaken by this small, but powerful vibration motor. Works great as an physical indicator without notifying anyone but the wearer. This version uses a surface mount motor which is less likely to be damaged during use.


  • 20mm outer diameter
  • Thin 0.8mm PCB

Quantity : 1


Arduino LilyPad USB – ATmega32U4

An updated version the Simple board to create the LilyPad USB by replacing the classic ATMega328 with the new ATMega32U4. Not only does that mean that it’s running a variation of the latest and greatest bootloader, but it also means no more FTDI Basic. The only extra piece of hardware you need to program the LilyPad USB is a micro-USB cable, since the new IC has built-in USB support. The LilyPad USB is also officially supported in the Arduino IDE as of version 1.0.2.

Just like the LilyPad Simple, this board features a JST socket so you can directly connect a Li-Po battery for power and an on-board power switch so you can turn it off when you’re not feeling particularly blinky. These boards were designed to streamline your next sewable project by keeping things simple and giving you more room to work while eliminating the need to sew a power supply. The LiPo battery is even rechargeable through the board, no more special external LiPo chargers are required.


  • 50mm outer diameter
  • Thin 0.8mm PCB

Quantity : 1

(GPS) 20 Channel EM-406A SIRF III Receiver with Antenna


The EM-406A GPS module from USGlobalSat based on the spectacular SiRF StarIII chipset. This complete module is built upon the same technology as the ET-301, but includes on-board voltage regulation, LED status indicator, battery backed RAM, and a built-in patch antenna! 6-pin interface cable included.


  • Weight: 16g including cable
  • 20-Channel Receiver
  • Extremely high sensitivity : -159dBm
  • 10m Positional Accuracy / 5m with WAAS
  • Hot Start : 1s
  • Warm Start : 38s
  • Cold Start : 42s
  • 70mA at 4.5-6.5V
  • Outputs NMEA 0183 and SiRF binary protocol
  • Smallest complete module available: 30mm x 30mm x 10.5mm

Quantity : 2

Nokia N96


Nokia N96 smartphone has built-in GPS and video and audio recording capability. It is suitable for location-based research and documentation (e.g. using www.locoblog.com). Note that phones do not come with a SIM card or contract, this must be supplied by the researcher.


  • GSM/WCDMA dual mode portable multimedia computer supporting EGSM 850/900/1800/1900, WCDMA 900/2100 HSDPA, WLAN and DVB-H Video.
  • Use the Nokia N96 for connecting to mobile Broadband using WLAN or HSDPA (3.5G) with faster downloading than 3G.
  • Find directions and locations with the integrated A-GPS and included maps.
  • Use the Nokia N96 to take photos with a 5.0 megapixel auto focus camera.
  • Enjoy videos, music and graphics on the 2.8” QVGA (240 x 320 pixels), 16M color display.
  • Listen to music with using the built-in stereo speakers.
  • Additional features include UPnP, Bluetooth 2.0 +EDR and USB 2.0 High-Speed.

Full details and specifications are on the manufacturer’s website here.

Kit Inventory

Kits include the following. Please report any missing items to the FASS IT Workshop as soon as possible.

  • Nokia N96 phone
  • Remote control
  • Earbud headphones
  • USB cable A – micro
  • Jack to 3 phono cable
  • Euro socket power charger
  • Euro socket USB power charger
  • Car Charger
  • Nokia N96 CD
  • Nokia N96 manual

Kits Available

There are 5 kits available, identified by the university asset code or product IMEI code.

Kit 1 (Galileo): Nokia N96 Assest Code FS01480 / IMEI 356406027024453.

Kit 2 (Compass): Nokia N96 Asset Code ? / IMEI 356406025404673.

Kit 3 (Beidou): Nokia N96 Assest Code FS01479  / IMEI  356406025404889.

Kit 4 (Glonass):

Kit 5 (QZSS):

HQR Bullet Camera


The HQR-C2 is a small DVD-quality digital video recorder that can be headmounted. It is a Picture in Picture (PiP) high-quality bullet camera (or ’sports’ camera) system for both in-car or on-bike setup.


  • MPEG 2 and 4 video recording.
  • 32GB CF card support.
  • 8hrs recording on one card at full quality.
  • Battery back-up system.
  • 720 x 576 resolution.
  • 8000kb/s bit rate.
  • Supplied with suction mount.
  • Internal mic with external inputs for additonal mic or Intercom connection.

Kit Inventory

The following items come with the kit. Please contact FASS IT Workshop if any items are missing as soon as possible.

  1. DCS HQR-C2 PiP Digital Video Recorder
  2. material bag
  3. UK Mains Charger
  4. IR Remote Control
  5. Camera dual split cable
  6. 16GB Dogcam high Speed CF
  7. Card reader
  8. USB cable A to mini
  9. UTP Ethernet cable
  10. 2 x 2m camera lead extension
  11. LANC camera remote
  12. CD manual
  13. HQ2 Headset mount
  14. 2 x Camera mount
  15. 2 x HQ Bullet DSP Colour CCD Camera
  16. 2 x lens covers
  17. Hard Carry case
  18. Belt Clip
  19. Lemo twin input video cable

Kits Available

There is 1 kit available, identified by the university asset code FS01484 / Serial Number ?