Tag Archives: Xbee

XBee Explorer Dongle v2

Posted on by

11697_00__65586.1410944998.1280.1280

This is the XBee Explorer Dongle unit for the Digi XBee module line. With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee. No cables needed. This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version.

Information

  • The on-board voltage regulator is good up to 500mA.
  • The highlight of this board is an FT231X USB-to-Serial converter. That’s what translates data between your computer and the XBee.
  • Reset button
  • Voltage regulator to supply the XBee with plenty of power.
  • Four LEDs that’ll help if you ever need to debug your XBee: RX, TX, RSSI (signal-strength indicator)
  • Power indicator.

This board also breaks out each of the XBee’s I/O pins to a pair of breadboard-compatible headers. So if you want to make use of the XBee’s extended functionality, you can solder some header pins into those, or even just solder some wire.

Quantity : 2

XBee Pro 50mW Wire Antenna – Series 2 (ZB)

Posted on by

10421-04__58265__35995.1368471810.1280.1280

This is the XBee XBP24-BZ7WIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.

Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules, they are not compatible with the outdated Series 2.5 Modules.

Information

  • 3.3V @ 295mA
  • 250kbps Max data rate
  • 63mW output (+17dBm)
  • 1 mile (1600m) range
  • Wire Antenna
  • Fully FCC certified
  • 6 10-bit ADC input pins
  • 8 digital IO pins
  • 128-bit encryption
  • Local or over-air configuration
  • AT or API command set

Quantity : 2

Arduino Breakout Boards

Posted on by
09269-01

Triple Axis Accelerometer Breakout – ADXL335

Breakout board for the 3 axis ADXL335 from Analog Devices. This is the latest in a long, proven line of analog sensors – the holy grail of accelerometers.

Information

  • The ADXL335 is a triple axis MEMS accelerometer with extremely low noise and power consumption – only 320uA!
  • The sensor has a full sensing range of +/-3g.
  • There is no on-board regulation, provided power should be between 1.8 and 3.6VDC.
  • Board comes fully assembled and tested with external components installed.
  • The included 0.1uF capacitors set the bandwidth of each axis to 50Hz.

Quantity : 2

10496-01__67483__33463.1368472070.1280.1280

GS407 Breakout Board

This is a breakout board to allow simple access to the tightly pitched pins on the GS406 and GS407 GPS units.

Information

  • This board breaks out all of the necessary pins to a row of standard 0.1″ spaced header to allow for easy bread boarding and simple connection.
  • Note: TXO and RXI are labeled according to the GS407 datasheet, which is from the point of view of the MCU. Therefore, TXO should connect to TX on your microcontroller, and RXI should connect to RX.
  • Note: This is not compatible with the newer GS407 module, as it uses a different connector completely. Please check to make sure this board will work with your module. ktxbai!

Quantity : 2

XBEE_BRAKOUT_001__33349__62354.1368470919.1280.1280

Breakout Board for Xbee Module

This is a simple breakout board for the popular XBee product from Digi.

Information

  • This board breaks out all 20 pins of the XBee to a 0.1″ standard spacing dual row header.
  • The spacing between 0.1″ headers is 0.5″ making it breadboard DIP friendly.
  • We highly recommend using the female sockets to avoid having to solder the XBee permanently to the breakout board.
  • This is the PCB only.

Quantity : 2

Arduino Boards

Posted on by
ArduinoUno_R3_Front_450px__56471__20476.1368472596.1280.1280

Arduino Uno – R3

The Arduino Uno is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

Information

  • Microcontroller – ATmega328
  • Operating Voltage – 5V
  • Input Voltage (recommended) – 7-12V
  • Input Voltage (limits) – 6-20V
  • Digital I/O Pins – 14 (of which 6 provide PWM output)
  • Analog Input Pins – 6
  • DC Current per I/O Pin – 40mA
  • DC Current for 3.3V Pin – 50mA
  • Flash Memory – 32 KB (ATmega328) of which 0.5KB used by bootloader
  • SRAM – 2KB (ATmega328)
  • EEPROM – 1KB (ATmega328)
  • Clock Speed – 16MHz

Quantity : 4

halfboard_LRG__38170__71109.1368472541.1280.1280

Half Size Breadboard

This half sized breadboard (2.2″ x 3.4″) is perfect for small projects and can be “snapped” together for larger ones. If a smaller board is required you can easily pull off the power rails or cut it in half using a saw to create 2 tiny breadboards.

Quantity : 10

12045-04__75102.1413881075.1280.1280

Bread board mini modulare blue

This blue Mini Breadboard is a great way to prototype your small projects.

Information

  • With 170 tie points there’s just enough room to build and test simple circuits.
  • Great for breaking out DIP package ICs to jumper wires!
  • If you run out of room, no worries, these mini breadboards can be snapped together to form larger stretches of board.
  • It has a peel and stick adhesive backing as well as two mounting holes for M2 screws so you can anchor it down.

Quantity : 10

bw6_01__68572__52198.1368472820.1280.1280

Breadboard jumper wire pack

Information

  • Basic breadboard jumper wire pack.
  • Including 4 different lengths: 200mm,165mm,125mm and 80mm.
  • Perfect design for a breadboard.
  • Contains approx 65 pieces

Quantity : 5

Arduino Starter Kit

Posted on by

cbabfd3196ac2a679c9c189fb441b6a1.image.447x354

This kit walks you through the basics of Arduino and electronics in a hands-on way. You will be able to build 15 projects using components that let you control the physical world through different kinds of sensors and actuators.

Click here to find out what projects you can make.

Kit Includes

  • 1 Arduino Projects Book (170 pages);
  • 1 Arduino UNO rev.3;
  • 1 USB cable;
  • 1 Breadboard;
  • 1 Wood base;
  • 1 9V Battery snap;
  • 70 Hard cables;
  • 2 flexible cables;
  • 6 Photoresistors;
  • 3 Trimmer d10 kOhm;
  • 10 Pushbutton;
  • 1 Temperature sensors;
  • 1 Tilt sensor;
  • 1 LCD (16x2i);
  • 1 LED (white);
  • 1 LED (RGB);
  • 8 LED (red);
  • 8 LED (green);
  • 8 LED (yellow);
  • 3 LED (blue);
  • 1 CC motor 6/9V;
  • 1 Servomotor;
  • 1 Piezo;
  • 1 H bridge;
  • 2 photocoupler;
  • 5 BC547;
  • 2 IRF520;
  • 5 100nF capacitor;
  • 3 100uF capacitor;
  • 5 100pF capacitor;
  • 5 1N4007 diode;
  • 3 Transparent jelly (rosso, verde, blu);
  • 1 Male strip connector (40×1);
  • 20 220 Ohm resistor;
  • 5 560 Ohm resistor;
  • 5 1 kOhm resistor;
  • 5 4.7 kOhm resistor;
  • 10 10 kOhm resistor;
  • 5 1 MOhm resistor;
  • 5 10 MOhm resistor.

Quantity : 2